Specifications

Screw diameter 55 mm
Output 275 kg/h
Type Single screw
-------------------
Worked hours
Hours under power
State good
At local norms ---------
Status

Description

Coextrusion Blow film line 3 layers CMG 55/75/55LHE – SW 2200 TA
Year of production 2018

1. Extruder A – Single screw extruder 5530/LHE
- Screw diameter 55 mm
- L/D ratio 30/1
- Extruder drive – 66 kW AC
- Nominal output in LDPE MFI 1.0 130 kg/h
- Lever type screen changer

2. Extruder B – Single screw extruder 7530/LHE
- Screw diameter 75 mm
- L/D ratio 30/1
- Extruder drive – 118 kW AC
- Nominal output in LDPE MFI 1.0 275 kg/h
- Lever type screen changer

3. Extruder C – Single screw extruder 5530/LHE
- Screw diameter 55 mm
- L/D ratio 30/1
- Extruder drive – 66 kW AC
- Nominal output in LDPE MFI 1.0 130 kg/h
- Lever type screen changer

4. 3-Layer Blow film co-extrusion die CBH500 F/3S-IBC with D 275 mm, LDPE, gap 1,6 mm

5. Internal bubble cooling system
- Introduction air fan 7,5 kW with heat exchanger battery
- Extraction air fan 7.5 kW
- Ultrasonic control system with 3 sensors for diameter control

6. Double flow high performance Air ring with integrated automatic thickness control type CR350/2 KARAT 2
- KUNDIG capacitive head for thickness reading installed on railways
- Blower for cooling ring 15 kW with inverter and heat exchanger battery

7. Batch gravimetric dosing and extrusion control system DOTECO
- 3 gravimetric dosing units GRADO ADROIT with 4 components each
- resin hopper loaders on each component with centralized vacuum pump
- control of haul-off speed
- control of individual extruder speed
- control in g/m, kg/h or micron

8. Basket 2200 RA with carbon rolls with motorised opening and closing and up – down moving with remote control from operator’s interface

9. Horizontal oscillating take-off unit HO 2200/Rev-C
- Nominal width 2200 mm
- Film width 2100 mm
- Nip roller with water cooling
- Oscillation - AC motor with inverter controlled speed
- Gusseting triangles with motorised opening and closing with remote control from operator’s interface
- Layflat pannels with motorised opening and closing with remote control from operator’s interface

10. Web center guide Erhardt Leimer EL2200

11. In line hot knife cut and seal device

12. Single station automatic winder TA 2200 SW
- Nominal width 2200 mm
- Film width 2100 mm
- Core diameter 76 mm (3”)
- Speed range 0-100 m/min
- Max roll diameter 800 mm

Please note that this description may have been translated automatically. Contact us for further information. The information of this classified ad are only indicative. We recommend to check the details with the seller before a purchase


Client type User – large company
Active since 2017
Offers online 15
Last activity Dec. 20, 2024

Description

Coextrusion Blow film line 3 layers CMG 55/75/55LHE – SW 2200 TA
Year of production 2018

1. Extruder A – Single screw extruder 5530/LHE
- Screw diameter 55 mm
- L/D ratio 30/1
- Extruder drive – 66 kW AC
- Nominal output in LDPE MFI 1.0 130 kg/h
- Lever type screen changer

2. Extruder B – Single screw extruder 7530/LHE
- Screw diameter 75 mm
- L/D ratio 30/1
- Extruder drive – 118 kW AC
- Nominal output in LDPE MFI 1.0 275 kg/h
- Lever type screen changer

3. Extruder C – Single screw extruder 5530/LHE
- Screw diameter 55 mm
- L/D ratio 30/1
- Extruder drive – 66 kW AC
- Nominal output in LDPE MFI 1.0 130 kg/h
- Lever type screen changer

4. 3-Layer Blow film co-extrusion die CBH500 F/3S-IBC with D 275 mm, LDPE, gap 1,6 mm

5. Internal bubble cooling system
- Introduction air fan 7,5 kW with heat exchanger battery
- Extraction air fan 7.5 kW
- Ultrasonic control system with 3 sensors for diameter control

6. Double flow high performance Air ring with integrated automatic thickness control type CR350/2 KARAT 2
- KUNDIG capacitive head for thickness reading installed on railways
- Blower for cooling ring 15 kW with inverter and heat exchanger battery

7. Batch gravimetric dosing and extrusion control system DOTECO
- 3 gravimetric dosing units GRADO ADROIT with 4 components each
- resin hopper loaders on each component with centralized vacuum pump
- control of haul-off speed
- control of individual extruder speed
- control in g/m, kg/h or micron

8. Basket 2200 RA with carbon rolls with motorised opening and closing and up – down moving with remote control from operator’s interface

9. Horizontal oscillating take-off unit HO 2200/Rev-C
- Nominal width 2200 mm
- Film width 2100 mm
- Nip roller with water cooling
- Oscillation - AC motor with inverter controlled speed
- Gusseting triangles with motorised opening and closing with remote control from operator’s interface
- Layflat pannels with motorised opening and closing with remote control from operator’s interface

10. Web center guide Erhardt Leimer EL2200

11. In line hot knife cut and seal device

12. Single station automatic winder TA 2200 SW
- Nominal width 2200 mm
- Film width 2100 mm
- Core diameter 76 mm (3”)
- Speed range 0-100 m/min
- Max roll diameter 800 mm

Please note that this description may have been translated automatically. Contact us for further information. The information of this classified ad are only indicative. We recommend to check the details with the seller before a purchase


Specifications

Screw diameter 55 mm
Output 275 kg/h
Type Single screw
-------------------
Worked hours
Hours under power
State good
At local norms ---------
Status

About this seller

Client type User – large company
Active since 2017
Offers online 15
Last activity Dec. 20, 2024

Here is a selection of similar machines

CMG 55/75/55LHE – SW 2200 TA Extrusion line