Specifications

Capacity - Diameter 165 mm
-------------------
Worked hours
Hours under power
State excellent
At local norms ---------
Status visible

Description

The machine is in top condition.
Ready for immediate use.
Complete new service - inspection
New media cylinders.
New media cylinder seals.
New oil filter.
Battery control unit - Buffer New.
With Media Cooling Unit - Air Conditioning


The pressurised flow lapping process enables high-quality results for machined components where
where quality defects from mechanical processes need to be eliminated. This makes the
AFM-Dynetics HL 30 process ideal for the following applications in the field of
Surface finishing:

Rounding: Achieving uniform radii.
Surface stress minimisation: Smoothing of critical fatigue points and removal of the notch effect
notch effect that can lead to the formation and expansion of cracks.
Polishing: Uniform improvement of the surface while retaining the component geometry.
component geometry.

Geometry optimisation: Improvement of the inlet and outlet openings and fine machining of surfaces
surfaces to improve the flow properties of the component.
ntburring:HL 30 Removal of burrs resulting from machining processes.
The HL 30 Dynetics AFM process is used for surface or edge machining of internal, external and otherwise difficult to access burrs,
external and otherwise difficult to access holes, cuts and edges. The process
is highly efficient, precise and repeatable and is suitable for one-way or two-way flow applications.
applications.



Special features of this process:
Location North Rhine-Westphalia, GermanyThis offer is subject to change and non-binding. Changes, errors and prior sale expressly reserved.Versatility. The Dynetics HL 30 AFM process is suitable for any material, includingtitanium, superalloys and materials that have been hardened or are otherwise difficult to machine.difficult to machine.

Precision. Material removal can be performed in targeted and hard-to-reach areas, such as cross and lateral holes.
Process efficiency. Both rough and finish machining are possible in a single operation.possible in a single operation.Customisability. The abrasive media can be adapted to the requirements of specific applications.to the requirements of specific applications.Quality and repeatability.The AFM process provides process control for consistent quality andquality and high repeatability.
Improved component performance. The AFM process can improve the flow behaviour of air, gas or liquidsor liquids on a component and reduce or eliminate the tendency to cavitate.eliminate cavitation.

Please note that this description may have been translated automatically. Contact us for further information. The information of this classified ad are only indicative. We recommend to check the details with the seller before a purchase


Client type User – small or medium company
Active since 2023
Offers online 4
Last activity Oct. 22, 2024

Description

The machine is in top condition.
Ready for immediate use.
Complete new service - inspection
New media cylinders.
New media cylinder seals.
New oil filter.
Battery control unit - Buffer New.
With Media Cooling Unit - Air Conditioning


The pressurised flow lapping process enables high-quality results for machined components where
where quality defects from mechanical processes need to be eliminated. This makes the
AFM-Dynetics HL 30 process ideal for the following applications in the field of
Surface finishing:

Rounding: Achieving uniform radii.
Surface stress minimisation: Smoothing of critical fatigue points and removal of the notch effect
notch effect that can lead to the formation and expansion of cracks.
Polishing: Uniform improvement of the surface while retaining the component geometry.
component geometry.

Geometry optimisation: Improvement of the inlet and outlet openings and fine machining of surfaces
surfaces to improve the flow properties of the component.
ntburring:HL 30 Removal of burrs resulting from machining processes.
The HL 30 Dynetics AFM process is used for surface or edge machining of internal, external and otherwise difficult to access burrs,
external and otherwise difficult to access holes, cuts and edges. The process
is highly efficient, precise and repeatable and is suitable for one-way or two-way flow applications.
applications.



Special features of this process:
Location North Rhine-Westphalia, GermanyThis offer is subject to change and non-binding. Changes, errors and prior sale expressly reserved.Versatility. The Dynetics HL 30 AFM process is suitable for any material, includingtitanium, superalloys and materials that have been hardened or are otherwise difficult to machine.difficult to machine.

Precision. Material removal can be performed in targeted and hard-to-reach areas, such as cross and lateral holes.
Process efficiency. Both rough and finish machining are possible in a single operation.possible in a single operation.Customisability. The abrasive media can be adapted to the requirements of specific applications.to the requirements of specific applications.Quality and repeatability.The AFM process provides process control for consistent quality andquality and high repeatability.
Improved component performance. The AFM process can improve the flow behaviour of air, gas or liquidsor liquids on a component and reduce or eliminate the tendency to cavitate.eliminate cavitation.

Please note that this description may have been translated automatically. Contact us for further information. The information of this classified ad are only indicative. We recommend to check the details with the seller before a purchase


Specifications

Capacity - Diameter 165 mm
-------------------
Worked hours
Hours under power
State excellent
At local norms ---------
Status visible

About this seller

Client type User – small or medium company
Active since 2023
Offers online 4
Last activity Oct. 22, 2024

Here is a selection of similar machines

Extrude Hone AFM Druckfliessläppmaschine Dynetics HL30