Showing 141 - 160 out of 221
Year:
One Used Fitzmill Model D-6 this unit is manufactured by Fitzpatrick and is a Pan feed Unit. Unit is completely made of 304 Stainless Steel including base on castors. The unit comes with a vibratory pan feeder, 16 swinging impact edge/knife edge blades, (D-225-0125) and is equipped with a 7-1/2 HP, 3/60/575 volt drive, 1745 rpm. Overall dimensions: 48 X …Year: 2002
Used 450 mm x 200 mm LabTech Scientific two roll mill, model LRM-SCR-200/3E, carbon steel construction with chromed rolls, PC controls with touchscreen interface, 28.5 kw motor, 480 volts, 3 phase, built 2002.Year: 1972
Used 350HP Hammer Mill. Manufactured by Gruendler. Model 50XD Wood Hog. 4'11" x 6'1" Inlet. 350 HP 575/60/3 motor. Overall 13'10"L x 6'11"W. Built 1972Year:
Used JBT Foodtech Finisher, Model UPF200. Paddle type finisher. Primary juice flow 50 - 150 gpm. Pulpwash flow 25 - 95 gpm. Oil recovery flow 48 - 120 gpm. d-Limonene recovery flow 33 - 100 gpm. Mounted on frame. 30-1/2" wide x 36" long x 26" deep chamber. 3" diameter shaft with 2-1/2" wide x 1/2" thick spiral blade. 34" …Year: 1985
Used Nelmor Granulator. Model 810RGII, New 1985 Has an 8″ X 10″ throat opening with a 2-knife semi-open rotor. Rotor is belt driven by a 5 HP motor460/3/60. Unit is factory sound enclosed, and is set up for veyor discharge. Hopper tilts open for quick clean out. With motor starter.Year:
Used approximately 13.75″ wide x 4.5″ o.d. Schwaberthan Polymix 110 P laboratory 2-roll mill. Electric heated rolls with water cooling. Includes a temperature control panel, roll mounted safty cage, 2.6KW 277/480 volt, 60Hz gear head motor Maunually adjusted roll spacing.Year: 2000
Used 2 liter Netzsch media mill, model LMZ2, 2 liter jacketed bowl, 10 hp xp motor, with operator panel only, on baseYear: 2020
Used SAS Mazzoni vacuum plodder, type Duplex plodder B-350, two stage with dual screw upper stage with die face cutter in vacuum chamber, lower stage with bar forming conical discharge, individually driven stages with motors and gearboxesYear: 1985
Used Nelmor Granulator. Model 810RGII, New 1985. Has an 8″ X 10″ throat opening with a 2-knife semi-open rotor. Rotor is belt driven by a 5 HP motor, 460/3/60. Unit is factory sound enclosed and is set up for veyor discharge. Hopper tilts open for quick clean out.Year:
Andritz Sprout-Bauer Model DSF1518 granulator, 7-knife rotor, 2 bed knife, 30 HP 460 volt only motor, belt drive, 5″ X 18″ blow-in in-feed hopper, vacuum take-off discharge, mounted on a short leg base, no starter/controls designed for film granulation (3 available). Previously used for recycling polyester film edge trim.Year: 1985
Used Nelmor Granulator. Model 810RGII, New 1985. Has an 8″ X 10″ throat opening with a 2-knife semi-open rotor. Rotor is belt driven by a 5 HP motor, 460/3/60. Unit is factory sound enclosed and is set up for veyor discharge. Hopper tilts open for quick clean out. With motor starter.Year:
Used Fluid Air hammer mill, model 007, stainless steel construction, screw feeder driven by 1.5 hp, 230/460 volt xp motor, missing screw, 10 hp, 230/460 volt, XP, main shaft motor, on stainless steel baseYear: 2016
2016 Goodnature EG260 Mill & X1 Press Model EG260, With 10 HP 1,760 RPM 460 volts 60 hz 3-phase stainless steel clad motor. with X1 Press Serial no 22057 -1 460 Volts -60 hz -3 phase Stainless steel control panels with safety enclosure. Portable unit on stainless steel stand with caster wheels.Year: 2010
Mill Powder Tech Solutions Mill Model HS800 with a 10 HP -240-480 Volt -1740 RPM -60 HZ Gear Drive, Stainless steel contact , with a 16" x 16 "stainless steel infeed hopper. with approx. 7.5" auger, to a 6" outfeed with 1/16" perforated s/s screen with (2) 1" bottom outlets, mounted on a stainless steel stand. MFG 2010.Last used at …Year: 1996
Used LR Systems Granulator. Model SG400, new 1996. Has 16″ X 16″ throat opening. Driven by an approximately 25 HP granulator. Includes motor starter and 5 HP blower for discharge. Also includes oversized hopper for accepting air conveyed scrap bottles, 48″ O.D. X 76″ straight side. Grinder and oversized hopper are mounted on portable base. Previously used for scrap blow …Year:
One pre owned Gemco 3 Cu. Ft. Stainless Steel Portable Slant Cone Blender with Hi Speed Agitator (bar is missing) - 316 S/S Contact Parts. Density Rated at 90 lbs/cf .Unit mounted on portable S/S frame with Lexan safety doors and casters. Blender has provisions for a Hi Speed intensifier bar (Not included) driven by 3HP/1.5 HP 3/60/480 Volt motor, …Year:
ONE USED Fitzmill milling machine. Manufactured by Fitzpatrick, Model D6 Pan Feed Fitzmill. All stainless steel contact parts, 6 inch chamber. Machine has a 5 HP, 220/440 Volt motor, S/S contact parts, pan feed, swinging blades.Year:
One Used Fitzmill model D6. This unit is manufactured by Fitzpatrick and is a Model D6 Fitzmill. Machine has a 5 HP, 220/440 Volt motor, S/S contact parts, pan feed, swinging blades (sharp/blunt). This machine is portable on wheels and has a painted frame.